The Kakute F4 V2.4 is ready for DJI HD. Easily plug in and power your HD video transmitter (like DJI O3 Air Unit & Caddx Vista) with its on-board 9V/A regulator, plus 5 dedicated UARTs w/inversion for peripherals. This stack comes with abarometer, plus LED/buzzer pad & I2C for external GPS/Magnetometers. The Tekko32 is the first 4in1 ESC, featuring the powerful F4 MCU @150Mhz, giving you smooth control & fast response, 4~6S & BLHeli32 for 30×30 stack/combo. This stack will come with an Atlatl HV V2 800mW VTX that iscompatible with all major FPV receivers.

Check out all our30×30 Stacksandthe rest of ourHolyBroselection!

Features

• Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
• Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.
• SmartAudio input allows remote control by the flight controller. Change channel, transmitpower, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.
• All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.
• MMCX connector is durable and easy to use. Rated for 100s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.
• LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad.
• Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.
• 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.
• Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly.
• Standard 36mm form factor allows you to mount the Atlatl directly on your flight controller stack.
• New and fasterF4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)
• PWM Frequency: 16k to 96k
• Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.

Specifications

Holybro Kakute F4 HD V2.4 2-8S 30×30 Flight Controller

• MCU: STM32F405
• IMU: MPU6000
• Barometer: BMP280
• OSD: AT7456E
• 5x UARTs (1,3,4,4,6,7)
• 128 Mbit Dataflash chip
• Battery input voltage: 2-8S
• BEC 9V/3A – Optimized for DJI O3 Air unit
• BEC 5V/2A
• 7x PWM Outputs (6 Motor Output, 1 LED)
• Supports serial receivers (SBUS, iBus, Spektrum, Crossfire, ESLR).
• Mounting: 30 x 30mm, 4mm hole with M3 Grommets
• Dimension: 37x37mm
• Weight: 7g
• JST-SH1.0_8pin port (For 4in1 ESCs)
• JST-SH1.0_6pin port (For DJI/Caddx HD System and other VTX)

Tekko32 F4 4in1 50A ESC

• Continuous Current: 50A x4
• Burst Current: 60A x4
• Supports 4-6S battery
• Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.
• ESC telemetry Supported
• Onboard analog current sensor
• No output BEC
• BLHeli_32 firmware
• 1000uf 35v capacitor included (highly recommended for 6s setup)
• Amperage meter scale ratio: 120 (V1.9Version)
• Dimensions:48x37x6mm / Weight:13.8g
• Mounting holes: M4 30.5×30.5mm (M3 grommets included)

Atlatl HV V2

• Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
• Audio: 6.5 MHz Mono
• Protocol smart audio 2.0
• Antenna Connector: MMCX
• Input Voltage: 7 to 28 volts (2-6S LiPo) with an absolute maximum 42 volts
• Dimensions: 35x25x7mm (Includes USB height)
• Mounting Holes:Standard 30.5mm square to center of holes
• Weight:9.3g

Includes

• 1x Holybro Kakute F4 HD V2.4 4-6S 30×30 Stack/Combo (F405 FC/ 50A F4 32bit 4in1 ESC & Atlatl HV V2 800mW VTX)
• 1x Wiring Kit

Wiring Diagram