TheHappymodel Crux3 ELRS 1S Toothpickis an excellent micro racing drone that comes with the Crazybee flight controller, EX1202.5 brushless motors, ELRS, and theCaddx Ant Camera to give you a great flying experience!

Note: Action Cameras are not included.

Update log:

• The Crux3 1S ELRS v2.0 version comes with ELRS F4 2G4 V3.1 which was built-in OPENVTX could support max 400mw output. Please use following vtxtable at the bottom of this page.
• Update Gyro to the ICM42688P instead of the MPU6000.

Check out The Happymodel Crux3 Collection, all our Analog BNF Drones and the rest of our Happymodel Products!

VIDEO:ExpressLRS Makes The Difference // Crux3 1S ELRS // No More Range Issues

Features

• 40gram 1s brushless Toothpick drone
  
• AIO Flight controller with ELRS Receiver and 5.8G VTX
  
• CADDX ANT Camera
  
• New 1202.5 KV11500 brushless motor
  
• Recommend to use 1s 450mah/650mah/660mah/720mah battery
  
• Compatible with CaddxFPV Peanut and Insta360 GO2
  
• Carrying Caddxfpv peanut Got 4.5 minutes flying time with 1s 650mah battery

Specifications

• Size: 97x97x35mm (without propellers)
• Weight: 40g (without battery)
• Wheelbase: 115mm

ONBOARD SPI EXPRESSLRS 2.4GHz RECEIVER

• Can be bound with All ExpressLRS 2.4GHz TX module, ExpressLRS firmware need 1.0.0 or the latest
• Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
• Receiver protocol to flight controller: CRSF
• Telemetry output Power: <12dBm
• Antenna: SMD antenna
• RF Frequency: 2.4GHz

ONBOARD 4-IN-1 ESC

• Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
• Factory firmware: O_H_5_REV16_7.HEX
• Support BLHeliSuite programmable
• MCU upgraded to EFM8BB21
• Default protocol: DSHOT300

CADDX ANT 1200TVL CAMERA

• Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
• Dimensions: 14*14mm(with a bracket to 19*19mm)
• TV System: NTSC or PAL Switchable
• Image Sensor: 1/3″ CMOS Sensor
• Min. Illumination: [email protected]
• Work Temperature: -20~+60
• Horizontal Resolution: 1200 TVL
• Wide Power Input: DC 3.7-18V
• S/N Ratio : >52dB (AGC OFF)
• Synchronization: Internal
• Auto Gain Control: YES
• Video Output: CVBS
• WDR: Global WDR
• DNR: 3D DNR
• Lens: 1.8mm
• IMAGE: 4:3
• Weight: 2g
• BLC: YES

CRAZYBEE FLIGHT CONTROLLER

• Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Power supply: 1S battery input (DC 2.9V-4.35V)
• Built-in SPI ExpressLRS 2.4GHz receiver
• Firmware target: CRAZYBEEF4SX1280
• Sensor: ICM42688P (SPI connection)
• Built-in Betaflight OSD(SPI Control)
• Built-in 5V 1A BECFlight controller
• Original whoop size compatible
• Built-in 5.8G VTX

EX1202.5 11500KV MOTOR

• Motor Dimensions: 14*14.5mm
• Shaft Diameter: 1.5mm
• Stator Diameter: 12mm
• Stator Length: 2.5mm
• No.of Cells (Lipo): 1S
• Configuration:9N12P
• Weight: 4.4g

ONBOARD 5.8G 40CH 25/200mW VTX

• Output power: 25mw~400mw switchable
• Frequency: 5.8GHz 5bands 37 channels
• Current consumption: 300mA (type)
• Input voltage: 3.3V 5.5V
• Smart audio ready
• Frequency: 37CH
• With Race band

GEMFAN 75mm PROPELLERS

• Center Hole diameter:1.5mm
• Center Thickness:5mm
• Prop Diameter:75mm
• Pitch:0.9in

Includes

• 1 xHappymodel Crux3 ELRS 1S Toothpick FPV Racing Drone – BNF
• 1x 3D Printed Camera Mount (Insta360 Go 2/Caddx Peanut)
• 1x Happymodel Zippered Carrying Case
• 2x Gemfan 75mm Propellers (Set of 4)
• 1x Caddx 5D OSD Menu Board
• 1x Accessories Kit