Skystars F7+KM65is a powerful stack for 5″freestyle and racing drones or 7-8″ long-range drones.The flight controller with modernF7processor has16MBmemory for blackbox and5V/3Aand10V/3ABEC. The flight controllercan be conveniently used on a drone with both digital and analog video transmission. The pads for connecting the LEDs are in the corners. The integratedbarometerfor altitude measurement also comes in handy.

The KM65 ESC supports 3-6S battery power and current up to 65A, which makes it playfully handle motors of size 2207-2808. The ESC has an aluminum heat sink on top to help dissipate heat better while protecting sensitive components from mechanical damage. The ESC uses a powerful F4 32-bit processor and AM32 firmware. Thus it supports telemetry, bidirectional DShot and PWM frequency up to 128KHz. The ESC is protected against voltage spikes by a TVS diode.

Check out all ourStacksand the rest of ourSkystars Products!

Features:

• 1. Solder pads are the largest in size compared to other FC in market.
• 2. Proper solder pad spacing to avoid solder bridge and facilitate easy soldering.
• 3. ESC connector on top-side rather than bottom which makes it easy for repair.
• 4. TVS Diode for Reverse Polarity Protection and Voltage Spike Suppression.
• 5. Powerful 3A BEC to supply all your electronics.
• 6. Pads arrangement are executed in such a way that when you twist the wires of the camera VTX and RX you don’t get any wire overlapping this gives you a uniform twist and clean look.
• 7. Support DJI O3 connector on the top side.
• 8. Support VTX ON/OFF Pit Switch.
• 9. Gyroscope independent power supply, No power lines near MPU6000 Gyro to avoid any EMI interference.
• 10. Two stages of Quality check to reduce any faulty electronic.
• 11. Comes ready with I2C support and INAV.

FC Specifications:

• MCU: STM32F722RET6 216MHz
• Gyroscope: MPU6000
• Baro:Bmp280
• OSD: Betaflight SPI OSD DJI HD OSD(UART6)
• Black box: 16MB
• 6x Uarts: UART 1/2/3/4/5/6
• 4x PWM outputs
• 1x I2C
• 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
• USB Type-C(USB2.0)
• 1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr)
• 1x JST-SH1.0_6pin connector (10V/Gnd/TX6/RX6/Gnd/Sbus)
• VTX 10V/Vbat filtered power ON/OFF Pit switch
• DJI FPV OSD is supported by any spare UART
• LED: 4 LED independent pads, support WS2812 programming lamp output.
• Receiver: Support Sbus, crsf, ibus, SBUS, XBUS, support 3.3v Spektrum satellite receiver, The default receiver input is UART1(You can solder ELRS RX on UART1), F7 has a built-in inverter, which can actually be installed in any spare UART.

Power:

• Input voltage: 3-6S
• BEC: 5V/10V 3A dual-channel BEC supports stable power supply on the sky side of DJI O3
• LDO 3.3V: Max.250mA
• Flight control onboard voltage sensor.

FC Firmware:

• BetaFlight firmware: SKYSTARSF722Pro
• INAV firmware:SKYSTARSF722HD

Mounting:

• Installation size: 30.5mm 30.5mm The installation hole is M4 and supports shock column installation
• External size 39mm 39mm
• Flight control weight: 6.9g

AM32-65A 4IN1 3-6S ESC BLheli32 128K DShot1200 4-in-1 ESC Specifications:

• Support 128K Dshot1200, Dshot600, Dshot300, Dshot150, Oneshot125, Multishot, PWM control signal
• Excellent over-current capability.
• Extreme stably support 6S LiPo battery with TVS.
• Excellent heat dissipation performance
• Better control performance F4 core MCU support 128K.
• Input voltage: 3-6S LiPo
• Con.Current: 65A
• Peak Current: 90A 10S
• Firmware: AM_32
• Support : Dshot 600/1200
• Mounting hole : 30.5mm/M3
• BEC: No
• Product size: 45.6*45*7.6mm
• Weight: 19g

Package Includes:

• 1x F7HD Pro4 FC
• 1x KM65 128K AM32 4IN1 ESC
• 8x Silicon grommets M4 to M3
• 2x JST-SH1.0_8pin cable, 4cm
• 1x JST-GH-6P cable for DJI port, 10cm